Historical FAQ (Frequently Asked Questions)
CoCut/EuroCUT reports "Invalid license data" or the code must be entered each time you start CoCut.
Please start the program one time as administrator.
Please go to the Windows start menu and
...
During the start of EuroCUT or CoCut the software show an error message "Invalid Code number".
There can be two reasons for this error message:
1. The number in brackets is not different from your
...
When the EuroCut/CoCUT setup is launched, the following error message occurs:
Error number: 0x80070725
Description: Incompatible version of the RPC stub
This error is caused by a DLL that was installed on the system, such as Oleaut32.dll, Olepro32.dll, Asycfilt.dll,
...
If the object height exceeds e.g. 70cm CoCut and EuroCUT are changing right into the segmentation dialog.
As default setting the Roland PNC 950 and 960 have their origin point at lower left. Nearly all other
...
How can I set the plotterīs origin point to the lower right position required by CoCut/EuroCUT?
Turn off the plotter and set the dip switch 6 to on. This activates the plotters Rotate function which
...
Although Ive activated the read back button in the cutting dialog the returned value is 0. How can I adjust my plotter so the right foil width value is returned?
The plotter has to be in the so-called host-mode. If you want to change the plotter settings, you first
...
When I try to cut objects, the error message unable to create cutter.dat appears.
The eurocut.ini file contains either no value or the wrong value for cutter.dat in the [Job] section.
...
Often EuroCUT is closed with the message copy protection not found while you are printing.
EuroCUT verifies the presence of the copy protection (dongle) at irregular intervals. When printing
...
I have linked two computers using Windows 95 in a peer-to-peer network. There is no problem in printing on a printer directly connected to the client computer. But it is not possible to make a printout on the second printer connected to the computer.
In this case you should assign an LPT port to the second computers spooler. To do this, open the
...
If you try to export a textblock from CorelDRAW6 to EuroCUT the message object has too many nodes appears.
CorelDRAW only has the ability to convert a limited number of nodes (approximately 3000). The more curves
...
The output quality of texts exported from CorelDRAW is very poor. Especially curves are often transmitted to EuroCUT with a jagged appearance.
This problem regularly occurs when cutting with CorelDRAW 3, 4 and 5, especially when cutting small characters.
...
What resolution should be used for vectorizing to obtain a good result?
If the quality of the original is good, use your scanners
optical resolution
such as 600 dpi.
...
After the installation of CoCut for CorelDRAW 7 I cant enlarge the symbol bar under Windows NT 4.
This problem only occurs when using CorelDRAW and Windows NT 4 and according to CorelDRAWs
technical
...
It often happens that fonts are not or incorrectly displayed or EuroCUT crashes while text is being typed.
So the
atmfonts.qlc
file, which is normally to be found in the c:\psfonts directory, has
...
When I export my job in bitmap format (JPEG, GIF, TIFF, etc.) I only get a bitmap with lines.
This problem only occurs when Windows NT is being used. Unfortunately it cannot be eliminated at present,
...
EuroCUT wont start and an error message copy protection not found appears. But the dongle can be detected without any problem using Windows 3.x or Windows 95.
Start Windows NT as administrator, insert program disk 3 (EuroCUT
Light
disk 2) into the
disk
...
The plotter cuts the first characters cleanly and then begins to draw indefinable curves.
This is a typical buffer overflow problem when the plotter is driven serially. This occurs when the flow control is not properly set up for serial transmission. For serial data transmission most plotters are driven with the following parameters:
...
Complete questions and answers
[
FAQ
]
Complete questions and answers